What are the classifications of tapered roller bearings?

Release time:

2023-09-08

Single row tapered roller bearings have an outer ring, an inner ring and a set of tapered rollers, which are composed of an inner ring assembly composed of a basket-shaped cage. The outer ring can be separated from the inner ring assembly. According to the ISO tapered roller bearing external dimension standard, any standard type of tapered roller bearing outer ring or inner ring assembly should be able to achieve international compatibility with the same type of outer ring or inner ring assembly. exchange.

Single row tapered roller bearings have an outer ring, an inner ring and a set of tapered rollers, which are composed of an inner ring assembly composed of a basket-shaped cage. The outer ring can be separated from the inner ring assembly. According to the ISO tapered roller bearing external dimension standard, any standard type of tapered roller bearing outer ring or inner ring assembly should be able to achieve international compatibility with the same type of outer ring or inner ring assembly. exchange. That is to say, the outer dimensions and tolerances of the same type of outer ring must comply with the provisions of ISO492 (GB307), and the cone angle of the inner ring components, the diameter of the cone of the components, etc. must also comply with the relevant regulations for interchangeability.
Usually, the cone angle of the outer ring raceway of a single row tapered roller bearing is between 10° and 19°, and it can withstand the combined effects of axial load and radial load at the same time. The larger the cone angle, the greater the ability to withstand axial load. Bearings with large cone angles have a suffix code of B. The cone angle is between 25° and 29°. They can withstand large axial loads. In addition, single row tapered roller bearings can adjust the clearance during installation.
The outer ring (or inner ring) of double row tapered roller bearings is a whole. The small end faces of the two inner rings (or outer rings) are similar, and there is a spacer in the middle. The clearance is adjusted by the thickness of the spacer, and the pre-interference of the double row tapered roller bearing can also be adjusted by the thickness of the spacer.
Four-row tapered roller bearings, the performance of this kind of bearing is basically the same as that of double-row tapered roller bearings, but it bears a larger radial load than double-row tapered roller bearings, and the limit speed is slightly lower. It is mainly used in heavy machinery.
Multi-sealed double and four-row tapered roller bearings, ZWZ provides long-life, multi-sealed double and four-row tapered roller bearings. Carry out a new personalized design for the bearing, change the traditional design method of the fully sealed bearing, and adopt a new type of sealing structure combining sealing and dustproof to improve the sealing effect and performance. Compared with open structure bearings, multi-sealed double and four-row tapered roller bearings have a service life increased by 20% to 40%; lubricant consumption is reduced by 80%.

Latest News

Deep groove ball bearings

Deep groove ball bearings play a crucial role in various machinery and equipment, ensuring smooth operation and efficient performance. Proper installation and maintenance are essential to ensure the longevity and reliability of these bearings.

2024-03-01

What are the classifications of tapered roller bearings?

Single row tapered roller bearings have an outer ring, an inner ring and a set of tapered rollers, which are composed of an inner ring assembly composed of a basket-shaped cage. The outer ring can be separated from the inner ring assembly. According to the ISO tapered roller bearing external dimension standard, any standard type of tapered roller bearing outer ring or inner ring assembly should be able to achieve international compatibility with the same type of outer ring or inner ring assembly. exchange.

2023-09-08

Precautions for bearing storage

In contact with corrosive chemical media, the bearing is not cleaned cleanly, there is dirt on the surface, or the bearing is touched with sweaty hands. After the bearing is cleaned, it is not packaged or installed in time, and it is exposed to the air for a long time, and is attacked by air moisture and contamination; contamination

2023-09-08

Installation method of deep groove ball bearings

Deep groove ball bearing installation method 1: Press fit: When the inner ring of the bearing is tightly matched with the shaft, and the outer ring is loosely matched with the bearing seat hole, a press can be used to press the bearing onto the shaft first, and then install the shaft together with the bearing. Put them into the bearing seat hole together. When pressing, place an assembly sleeve made of soft metal material (copper or mild steel) on the end face of the inner ring of the bearing.

2023-09-08

Bearing characteristics of deep groove ball bearings

Deep groove ball bearings are the most commonly used rolling bearings. Its structure is simple and easy to use. It is mainly used to bear radial load, but when the radial clearance of the bearing is increased, it has a certain performance of angular contact ball bearing, and can bear combined radial and axial loads. When the rotation speed is high and it is not suitable to use thrust ball bearings, it can also be used to bear pure axial load. Compared with other types of bearings with the same specifications and dimensions as deep groove ball bearings, this type of bearing has a small friction coefficient and a high limit speed. But it is not impact resistant and not suitable for bearing heavy loads.

2023-09-08

Physical properties of high temperature resistant materials for bearings

Porosity: refers to the percentage of pore volume in the material as a percentage of the total volume of the material. The pores of SKF bearing high temperature resistant materials can be divided into three types according to their existing forms: closed pores, one pores - pores connected to the outside atmosphere, connected pores - the proportion of the entire pores is 7L. Small SKF bearing high temperature resistant materials have the ability to resist erosion and structural strength; the higher the porosity, especially the more interconnected pores, the lower the thermal conductivity of the material. Lightweight adobe bricks, lightweight high-alumina bricks and other insulation materials use a method to increase porosity and reduce their thermal conductivity.

2023-09-08